Discover / Field note 01 / Engineering

Slower can
mean stronger.

Gears trade speed for turning force. Change a few teeth and see the trade happen.

By Knowhubs · 22 October 2026 · About 4 minutes + time to experiment

Open the model ↓
A pair of gears mounted to the Mechanical Playground assembly

One idea to take away

Count teeth, not guesses.

A 12-tooth driver must turn twice to move every tooth on a 24-tooth driven gear past the contact point. The driven gear therefore turns at half the speed. For two external gears, it also turns in the opposite direction.

Before touching the controls, predict this: if you halve the speed once, then halve it again, will 120 RPM become 60, 30 or 0?

Your workbench

Turn 120 RPM into something else.

IDEAL TWO-STAGE TRAIN
Two gear pairs connected by a shared shaftA has 12 teeth and drives B with 24. B and C share a shaft. C has 24 teeth and drives D with 24. A and D turn clockwise. B and C turn anticlockwise. Schematic tooth outlines.B + C: same shaft, same speedA↻ 12TB↺ 24TC↺ 24TD↻ 24TSTAGE 1STAGE 2
Tooth counts set the relative sizes. Shaft routing and tooth profiles are schematic; this is not a manufacturing drawing.
More controls · choose each gear
Choose the teeth on each gear
INPUT120 RPM ↻
INTERMEDIATE SHAFT60 RPM ↺
OUTPUT60 RPM ↻

120 × (12 ÷ 24) × (24 ÷ 24) = 60 RPM

Output speed is 0.5× the input. In an ideal lossless train, the torque factor is 2×. Two external meshes reverse direction twice, so the output turns the same way as the input.

Build a 30 RPM output.

Keep the input at 120 RPM. Open More controls to choose the teeth yourself, then check whether your two stages reduce the speed to one quarter.

Change any gear to clear the previous result.

Check your reasoning: compared with the input, is this output…

Choose an answer to check your explanation. There is no timer or score.

01 / What to notice

Two stages multiply.

Each pair has a driver and a driven gear. In this compound train, B and C are fixed to the same intermediate shaft, so they turn together. Multiply the speed factor of each pair to find the final speed.

With 12 teeth driving 24, each stage has a speed factor of ½. Two such stages give ½ × ½ = ¼. An input of 120 RPM becomes 30 RPM.

Try Cancel out. Stage one halves the speed; stage two doubles it. The output returns to 120 RPM. A large gear does not always make the final machine slower: the complete train matters.

02 / What you trade

Speed is not free power.

Torque means turning force. In an ideal lossless transmission, reducing speed to one quarter multiplies torque by four. Increasing speed fourfold reduces torque to one quarter. The gears change the trade, rather than creating energy.

A real gearbox also loses energy through friction and other effects. It must cope with loads, tooth stresses, alignment and heat. This workbench calculates ideal speed and torque factors; it does not simulate whether a machine can carry a load.

03 / Try it without the readout

Make 120 become 90.

You have the same five tooth counts on each gear. Can you combine a reduction and an increase to get an overall speed factor of ¾?

Reveal one solution and why it works

A = 12, B = 24, C = 36 and D = 24. Stage one reduces speed by ½; stage two increases it by 1½. Multiply them: ½ × 1½ = ¾, so 120 becomes 90 RPM. If you allow an unchanged second stage, A = 18, B = 24, C = 24 and D = 24 also gives 90 RPM. Different machines can produce the same overall ratio.

Then change only C. Explain to yourself why the output moves in that direction before checking the number.

Sources & model limits

The explanation was checked against FRCDesign’s Gear Basics and its Torque and Speed lesson. The two-stage calculation also matches the existing Knowhubs Gear Shift model. Diagram and text are original Knowhubs material.

The workbench offers five tooth counts: 12, 18, 24, 36 and 48. All combinations use two external gear meshes and a shared intermediate shaft. Geometry is illustrative. No friction, load, material strength or motor performance is modelled. This is an explanation of ratios, not a design or safety assessment.

Now use the idea

Can you tune all six machines?

Take the same relationship into Gear Shift. Pick the teeth, match the target and test your reasoning.

Play Gear Shift ↗